New & established homeowners
How Old Is My Water Heater? Find Any Appliance's Age
How to find your water heater's age from its label or serial number, with date codes for Rheem, A.O. Smith and Bradford White, plus other systems.
Most people ask “how old is my water heater?” at the worst possible moment: standing in a puddle, or on the phone with a plumber who wants to know before quoting a repair. The answer is usually sitting right on the tank. You just have to know where to look and how to read it.
This guide shows you how to find the age of your water heater, how to read the date code in the serial number for several common brands, and how to turn that one-off lookup into a simple whole-house list of what’s aging, what’s still under warranty and where every manual lives.
A safety note first. Everything in this guide is look-only. You shouldn’t need tools, and you shouldn’t need to open anything that’s wired or plumbed. If a label is hidden behind a panel on a gas appliance or an electrical unit, or you see scorch marks or notice a leak, stop and call a licensed professional. If you smell gas, leave the house and call your gas utility or emergency services from outside.
Where to find your water heater’s age
Step 1: Find the data plate
Every water heater has a label, often called the data plate or rating plate. On a standard tank it’s usually a sticker or metal plate on the side of the tank, often near the controls at the bottom. On a tankless unit it’s usually on the side or front of the cabinet.
The plate lists the manufacturer, model number, serial number, capacity and ratings. Take a clear photo of the whole thing. It will answer most future questions without another trip to the basement.
Step 2: Look for a printed date
Some data plates simply print the manufacture date, sometimes labeled “Mfg. date” or similar. If you see one, you’re done with this step.
Step 3: Decode the serial number
Many manufacturers don’t print the date outright. They encode it in the serial number instead, and each brand uses its own code. Several brands have also changed their code over the years, so a pattern that fits a newer tank may not fit an older one. Below are the patterns published by the manufacturers for a few common brands. If your serial doesn’t fit cleanly, don’t force a match. Ask the manufacturer.
Rheem
Rheem describes a 10-character serial number where the first two digits are the month and the next two are the year. A serial that starts 0918 means September 2018.
Some Rheem serials, especially ones that start with a letter, follow a different layout. If the first four digits don’t read as a real month and year, contact Rheem with your model and serial number.
Ruud
Ruud has a water heater age calculator on its website. Type in the serial number from the data plate and it tells you when the unit was made. That’s the simplest route for a Ruud tank.
A.O. Smith
On current A.O. Smith water heaters, the first two digits are the year and the next two are the week of manufacture (01 to 53). A serial that starts 1719 was made in the 19th week of 2017, which is around early to mid May.
Older A.O. Smith units used other layouts. If the first four digits don’t make sense as a year and a week, check with A.O. Smith.
Bradford White
Bradford White serials start with two letters. The first is the year and the second is the month.
Month letters run A (January) to M (December), skipping I, so H is August, J is September, K is October, L is November and M is December.
Year letters repeat on a 20-year cycle and skip I, O, Q, R, U and V. Bradford White’s current chart pairs each letter with two years:
| Letter | Year | Letter | Year |
|---|---|---|---|
| A | 2004 or 2024 | L | 2014 or 2034 |
| B | 2005 or 2025 | M | 2015 or 2035 |
| C | 2006 or 2026 | N | 2016 or 2036 |
| D | 2007 or 2027 | P | 2017 or 2037 |
| E | 2008 or 2028 | S | 2018 or 2038 |
| F | 2009 or 2029 | T | 2019 or 2039 |
| G | 2010 or 2030 | W | 2020 or 2040 |
| H | 2011 or 2031 | X | 2021 or 2041 |
| J | 2012 or 2032 | Y | 2022 or 2042 |
| K | 2013 or 2033 | Z | 2023 or 2043 |
For A, B and C, count the digits after the two letters. The production number is seven digits on units made before December 2007 and eight digits after, so A plus seven digits is 2004 and A plus eight digits is 2024. For D through Z, the later year hasn’t arrived yet, so SC means March 2018. Older tanks from the 1980s and 1990s reused the same letters, so if a tank looks decades old, confirm the date with Bradford White.
Other brands
We haven’t listed codes for other brands, including State, American, Whirlpool, GE, store brands and tankless-only makers, because we couldn’t confirm them from the manufacturer. For those, contact the maker with your model and serial number, or look for a lookup tool on its support site.
Even for the brands above, confirm the date with the manufacturer if it matters for a warranty claim or a replacement decision. Many brands have a warranty lookup on their support site that takes the serial number and shows the date along with any coverage.
Step 4: Remember that manufacture date isn’t install date
A water heater can sit in a warehouse or a store before it’s installed, so the install date is often a bit later than the manufacture date. To pin down the install date, check for:
- An installer’s sticker or tag on or near the tank
- Your receipt or invoice, if you had it installed
- A permit record, since many areas require a permit for water heater replacement
- Your home inspection report, if you bought the house
If you can only find the manufacture date, use it. It’s close enough for planning.
Finding the age of other major systems
The same method works for almost everything with a label: find the data plate, photograph it, look for a printed date, and ask the manufacturer if the date is encoded.
| System | Where the label usually is | Notes |
|---|---|---|
| Furnace | Inside or on the access door of the cabinet | If the label is behind a panel, ask your technician to photograph it at the next service |
| Central AC / heat pump outdoor unit | Side or back of the outdoor unit | Look only; don’t open the unit |
| Indoor air handler / coil | On the cabinet near the furnace | Can differ in age from the outdoor unit |
| Refrigerator | Inside, on a side wall or under the crisper drawers | Sometimes on the back |
| Dishwasher | On the edge of the door or the tub frame | Open the door and look along the rim |
| Washer / dryer | Inside the lid or door frame, or on the back | Front-loaders often have it around the door opening |
| Range / oven | Inside the storage drawer, oven door frame or back panel | Check the drawer first |
| Smoke and CO alarms | Printed on the back of the alarm | Twist the alarm off its base to read it (hardwired alarms may be plugged into a connector; don’t pull on wires, and reattach it right away) |
| Garage door opener | On the motor housing | Read it from a stable ladder; don’t touch springs or cables |
| Roof | No label | Check receipts, permits, the inspection report or ask a roofer |
Your heating and cooling equipment can have more than one age. The outdoor AC unit, the indoor coil and the furnace are sometimes replaced at different times, so record each one separately.
Typical lifespans: a rough guide, not a countdown
Once you know ages, the natural next question is “how long will it last?” Here are commonly cited ranges. Real lifespans vary widely with the model, the installation, maintenance, water quality, climate and how hard the equipment works.
- Tank water heater: often around 8 to 12 years.
- Tankless water heater: often cited as lasting longer than a tank; check the manufacturer’s figures for your model.
- Furnace: often around 15 to 20 years or more.
- Central AC: often around 10 to 15 years, sometimes less in hot climates.
- Heat pump: varies a lot with climate and use; ask your technician.
- Asphalt shingle roof: often around 20 to 30 years.
- Major kitchen and laundry appliances: often around 10 to 15 years, some less.
- Smoke and CO alarms: NFPA recommends replacing smoke alarms 10 years after the manufacture date. CO alarms often last about 5 to 10 years depending on the model, so check the label or manual.
A system near the end of its range won’t fail on schedule. Treat the range as a signal to watch for warning signs, get a quote and set money aside. Warning signs for a water heater include rusty water, rumbling noises, moisture around the base or less hot water than usual. If you notice any of those, have a plumber take a look, and call one right away if you see active leaking.
Build a whole-house systems list
Looking up all of your systems once, and writing it down, is what saves you. One list shows which systems are aging, which warranties are still active, and where the manual is when the dishwasher throws an error code at 9 p.m.
What to record for each system
| System | Brand & model | Serial | Manufacture / install date | Typical lifespan (approx.) | Warranty ends | Manual location | Last serviced | Notes |
|---|---|---|---|---|---|---|---|---|
| Water heater (tank, gas) | Often ~8 to 12 yrs | |||||||
| Furnace | Often ~15 to 20 yrs | |||||||
| Central AC (outdoor) | Often ~10 to 15 yrs | |||||||
| Refrigerator | Often ~10 to 15 yrs | |||||||
| Dishwasher | Check manufacturer | |||||||
| Washer | Check manufacturer | |||||||
| Dryer | Check manufacturer | |||||||
| Roof | Often ~20 to 30 yrs (asphalt) |
Copy it into a spreadsheet or notebook, delete what you don’t have, and add anything else your house has, like a sump pump, water softener or well pump.
Gather manuals and warranty details
For each row, find two things:
- The manual. Most manufacturers post manuals online, including many older models. Search the brand’s support page with your model number and save a copy where you’ll find it again.
- The warranty. Check your receipt, the registration card or the manufacturer’s site for what’s covered and for how long. Warranties often cover some parts longer than others, and some depend on registration or regular maintenance, so read the terms for your specific unit. Record the end date so you can see it coming.
A one-afternoon checklist
Work through this once and you’ll have the whole house mapped:
- Photograph the data plate on the water heater, furnace, AC or heat pump, and air handler (look-only)
- Photograph the labels on the fridge, dishwasher, washer, dryer and range
- Check the dates on the back of every smoke and CO alarm
- Find a printed date or decode each serial number, and confirm with the manufacturer when it matters
- Look for install dates in receipts, permits, stickers and your inspection report
- Save the manual and record the warranty end date for each item
- Note the last service date for anything that gets serviced
- Flag anything near the end of its typical range, then plan a quote and a savings goal
Keep it current
Update the list whenever something is serviced, repaired or replaced, ideally the same day, while the box and receipt are still in the house. If you keep a home maintenance log, the two work well side by side: the list says what you have, and the log says what’s been done to it. Many long-life habits, like flushing the water heater or changing HVAC filters, are on our home maintenance checklist.
When to call a professional
Finding an age is a look-only job. Almost anything past that belongs with a licensed pro: any gas appliance work, anything electrical beyond reading a label or pressing a test button, opening sealed panels, and a water heater that leaks, drips from the relief valve or makes loud popping or banging noises. For replacement decisions, a technician can judge the unit’s actual condition, which tells you more than its age alone.
A place to keep the whole-house list
If you’d like this set up for you, The Homeowner System ($29, works on the free Notion plan) is a Notion template with a warranty, manual and receipt vault for appliances, systems and big purchases. Next to it sits a seasonal maintenance calendar with a ready-made library of 35 tasks. Each has a usual month and day, a next-due date worked out for you, and a Mark done button that moves it to its next date. There’s also a service-provider directory and a room-by-room home inventory, and a free sample on the product page if you want to see the layout first.
FAQ
My data plate is faded or missing. How do I find the age?
Look for other labels on the tank or cabinet, such as an installer’s sticker or a second label near the controls. Check old photos, your home inspection report, permits and receipts. If you can read even the model number, the manufacturer may be able to help, and a plumber can usually give you a rough estimate from the unit’s style and condition.
Do tankless water heaters have a date code too?
Usually, yes. Rheem, for example, uses the same serial format on its tank, tankless and hybrid water heaters. The label is typically on the side or front of the cabinet. Confirm the date with the manufacturer if it matters.
Does the warranty start on the manufacture date or the install date?
It depends on the brand, so read your warranty terms. A.O. Smith’s residential warranties, for example, run from the original installation, and a claim asks for the purchase and installation dates. That’s a good reason to keep the install receipt with your systems list.
Should I replace an appliance just because it’s old?
Not necessarily. Age is a planning signal, not a deadline. An older unit that’s been maintained may run for years. Use its age to start budgeting and to ask your technician about its condition at the next service, rather than replacing it on age alone.